Honeywell Chronotherm Iv Plus User Manual
T8602d chronotherm® iv programmable thermostats, Mercury notice, Application
Nov 14, 2016 Hoe reset u de Honeywell Chrontherm 4? In deze instructievideo wordt getoond hoe u het fabrieksprogramma van een Honeywell Chronotherm IV klokthermostaat (T8602A-NL08) kunt. Honeywell control panel LYNX Plus User Manual Add to Favourites Lynx Plus Series Security System User Guide BYPASS NO DELAY RECORD TEST FUNCTION STATUSVOLUME PLAY CODE LIGHTS ON LIGHTS OFFCHIME ESCAPE ADDDELETE SELECT OFFSTAY132 AWAYAUX465 ARMED READY 79 8 0 800-03858V1 12/09 Rev. View and Download Honeywell Chronotherm IV T8611G installation instructions manual online. Deluxe Programmable Heat Pump Thermostats. Chronotherm IV T8611G Thermostat pdf manual download.
® U.S. Registered Trademark
Copyright © 2003 Honeywell International Inc. •
• All Rights Reserved
INSTALLATION INSTRUCTIONS
69-1510-4
T8602D Chronotherm® IV
Programmable Thermostats
APPLICATION
The T8602 Chronotherm® IV Programmable Thermostat
provides electronic control of 24 Vac single-stage heating
and cooling systems or 750 mV heating and 750 mV
cooling. Refer to Table 1 for a general description of the
thermostat. All T8602 Thermostats are powered by
batteries.
MERCURY NOTICE
If this control is replacing a control that contains
mercury in a sealed tube, do not place your old
control in the trash. Dispose of properly.
Contact your local waste management authority
for instructions regarding recycling and the
proper disposal of the old control.
INSTALLATION
When Installing this Product..
1. Read these instructions carefully. Failure to follow
the instructions can damage the product or cause
a hazardous condition.
2. Check the ratings given in the instructions and on
the product to make sure the product is suitable for
your application.
3. Installer must be a trained, experienced service
technician.
4. After completing installation, use these instructions
to check out the product operation.
Location
Install the thermostat about 1.5m (5 ft) above the floor in
an area with good air circulation at average temperature.
See Fig. 1.
Do not install the thermostat where it can be affected by:
— drafts, or dead spots behind doors and in corners.
— hot or cold air from ducts.
— radiant heat from sun or appliances.
— concealed pipes and chimneys.
— unheated (uncooled) areas such as an outside wall
behind the thermostat.
Wallplate Installation
The thermostat can be mounted horizontally on the wall
or on a 50.8 mm x 101.6 mm (2 in. x 4 in.) wiring box.
Position wallplate horizontally on the wall or on a
50.8 mm x 101.6 mm (2 in. x 4 in.) wiring box.
1. Position and level the wallplate (for appearance
only). The thermostat will function properly even
when not level.
2. Use a pencil to mark the mounting holes. See Fig.
Download & Install The latest version of FilmoraPro can always be downloaded from filmora.wondershare.com, or you can click the button below to download. Choose your operation system and then follow the instructions provided to finish the installation process. Filmora download for windows 10.
2.
3. Remove the wallplate from the wall and drill two
4.76 mm (3/16 in.) holes in the wall (if drywall) as
marked. For firmer material such as plaster, drill
two 5.56 mm (7/32 in.) holes. Gently tap anchors
(provided) into the drilled holes until flush with the
wall.
4. Position the wallplate over the holes, pulling wires
through the wiring opening.
5. Loosely insert the mounting screws into the holes.
6. Tighten mounting screws.
Table 1. Description of T8602 Thermostats.
T8602
System
Changeover
System
Selection
Fan
Selection
Honeywell Chronotherm Iv Plus User Manual
Comments
D
Heat-Cool
Manual or
Automatic
Selectable
Heat-Off-Cool or
Heat-Off-Cool-Auto
On-Auto
System and fan selections are done
by keyboard.
Honeywell Chronotherm Iv Plus Manual
- Installation
- Wiring
- Settings
- Installer setup
- Checkout